Home > Bicycle Engine Parts > Performance Parts > Nitrous Kits >

Aluminum Nitrous Oxide Boost Kit
Inject Nitrous into your Motor
 
Alternative Views:


Our Price: $59.99 Out of Stock


Product Code: ANOSK

choose a color

Color*:


 
Description
 
These nitrous kits are designed to mount directly to your handle bars so that you never have to remove your hands from the grips as you trigger the nitrous. You can rotate your handle bars completely from one side to the next. All kits come with high quality brass fittings, custom made velcro strap and over sized 3/8 OD , 1/4" ID Hose. The NOS dispenser is secured with a velcro strap or mount and use the Mounting Bracket. This allows you to easily refill your nitrous chargers as needed. The nitrous hose mounts directly into your intake system thru the airbox, air filter, intake manifold or thru the rear of your boost bottle with the fittings supplied.

NOS Kit Includes:

1 - NOS Trigger Dispenser Assembly (Available in 3 Colors)
5 - 16gm Nitrous Bottles
2 - Large Zip Ties
2 - Small Zip Ties
1 - 5' long Clear House
1 - Velcro Strap
1 - Brass NOS Jet Nozzle
1 - Mounting Bracket with strap
1- Installation Instructions


NOS can be injected into a motor in 2 basic ways:

Wet – NOS is injected into the fuel stream, usually in the intake manifold.
Dry – NOS is injected into the air stream, usually into the air cleaner or air box.

Both methods will work , but wet will give the best results. Oncer you decide on which way you want to inject you nitrous, now you can begin installation.

Nitrous Trigger Dispenser Installation

  1. Push button or trigger lever multiple times to insure its not stuck. Make sure it has good action and is not sticky. Don't want to waste the precious nitrous.

  2. Insert the nitrous bottle into unit, because of differences with nitrous bottle manufacturing it may be necessary to place some paper under the bottle to insure a good puncture. Once the bottle is punctured, do not remove or you will let all the nitrous escape.

  3. Screw the Brass NOS Jet nozzle onto the the trigger assembly.

  4. Place the Trigger assembly on the handlebars and attach it with the velcro strap and Large zip ties.

  5. Insert the Clear tubing onto the jet nozzle.

  6. Route the tubing to where the Brass threaded fitting will be installed.

  7. Use small zip tie to secure the hose to the Jet nozzle

Brass Barbed Fitting Installation

  1. Decide if you want to run wet or dry injection.

  2. Wet - injection it is best to remove the intake to install the fitting to avoid any shaving getting in the motor. We recommend using an intake with the pre drilled and taped intake.

  3. Dry – injection we recommend taking off the air cleaner or air box to avoid getting shavings into the motor.

  4. Use a 3/8 drill bit to make hole, use a smaller bit to make a pilot hole.

  5. For extra measure you can run a tap to make the threads, or just screw in the brass fitting to make threads. Threads are a 1/8” - 27 NPT (national pipe thread)-L1. You can get close with a 10mm X 1.25 pitch.

  6. Screw in Brass fitting

  7. Attach clear hose to fitting and secure with a small zip tie


May we also suggest...
Nitrous Oxide NOS 5 Pack Refill
Our Price: $14.99

Add
Nitrous Oxide NOS 5 Pack Refill
CNC Boost/NOS Intake Manifold
Our Price: $19.99

Add
CNC Boost/NOS Intake Manifold

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Bicycle Engine Parts > Performance Parts > Nitrous Kits
Bicycle Engine Parts > Aftermarket
Bicycle Engine Parts > Performance Parts
Bicycle Engine Parts > Bicycle Engine Parts - All
Bicycle Engine Parts